Leviton Switch VZI06 1L User Manual

Single Pole (One location) or 3-Way (Multi-location)  
Incandescent Dimmer  
Cat. No. VZIØ6-1L, 600W (Lighted)  
120VAC, 60Hz  
DI-000-VZI06-02A  
INSTALLATION INSTRUCTIONS  
WARNINGS AND CAUTIONS:  
WARNINGS AND CAUTIONS:  
To be installed and/or used in accordance with appropriate electrical codes and regulations.  
Dimmer may not operate with dioded lamps (Sylvania Designer 16™ or Philips PAR-16™).  
If you are unsure about any part of these instructions, consult a qualified electrician.  
Total minimum load must exceed 40W.  
To avoid overheating and possible damage to this device and other equipment, do not install to control a receptacle, fluorescent lighting, a motor- or a transformer-  
operated appliance.  
Dimmer may feel warm to the touch during normal operation.  
Recommended minimum wall box depth is 2-1/2".  
Use with incandescent or 120V halogen fixtures only.  
Maximum wire length from dimmer to all installed remotes cannot exceed 300 ft.  
Disconnect power at circuit breaker or fuse when servicing, installing or removing fixture.  
Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.  
Vizia™ dimmers are not compatible with standard 3-way or 4-way switches. They must be used with compatible Vizia™ remotes for multi-location dimming.  
Use only one (1) Vizia™ dimmer in a multi-location circuit with up to 9 coordinating remotes without LEDs or up to 4 matching remotes with LEDs. The remote(s) will  
turn the light on at the brightness level selected at the dimmer.  
Preparing and connecting wires:  
This dimmer can be wired using side wire terminal  
screws or through backwire openings. Choose  
appropriate wire stripping specifications accordingly.  
INSTALLING YOUR DIMMER  
Step 4a cont’d  
Step 4b cont’d  
Step 3  
Tools needed to install your Dimmer:  
Dimmer  
NOTE: Use check boxes  
when Steps are completed.  
Slotted/Phillips Screwdriver  
Pliers  
Electrical Tape  
Pencil  
Coordinating Remote (no LEDs)  
Dimmer  
Hot (Black)  
BK  
Do not use for  
incandescent  
WARNING: TO AVOID FIRE, SHOCK, OR DEATH;  
TURN OFF POWER at circuit breaker or fuse and test  
Step 1  
Hot (Black)  
Cutters  
Ruler  
BK  
BK  
applications.  
WH  
Green  
Ground  
Black  
that power is off before wiring!  
Changing the color of your Dimmer:  
Your Dimmer may include three color options. The Dimmer ships  
with the White frame attached. To change color of frame, proceed  
as follows:  
Strip Gage  
RD  
Green  
Ground  
Green  
Ground  
YL/RD  
(measure bare  
Black  
5/8"  
Line  
120VAC, 60Hz  
wire here or use  
(1.6 cm)  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
ON  
ON  
ON  
YL/RD  
RD  
OFF  
OFF  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
ON  
N  
YL/RD  
Load  
Line  
120VAC, 60Hz  
RD  
gage on back of  
Use Terminal for 3-Way or  
More Applications Only.  
For Single-Pole Applications,  
Do Not Remove This Label.  
Load  
Cut  
the dimmer)  
(if necessary)  
White  
OFF  
White  
Neutral (White)  
Neutral (White)  
WIRING DIMMER:  
Connect wires per WIRING DIAGRAM as follows:  
WIRING DIMMER:  
Connect wires per WIRING DIAGRAM as follows:  
NOTE: When using the coordinating remote without LEDs, the dimmer  
can be installed on either the Line or Load side of the 3-way circuit.  
NOTE: Maximum wire length from dimmer to all installed remotes  
cannot exceed 300 ft.  
Identifying your wiring application (most  
common):  
NOTE: If the wiring in the wall box does not resemble  
Step 2  
Green or bare copper wire in wall box to Green terminal screw.  
Line Hot wall box wire to terminal screw marked "BK".  
Load wall box wire to terminal screw marked "RD".  
Dimmer terminal screw marked "YL/RD" should have Red  
insulationlabel affixed.  
any of these configurations, consult a qualified electrician.  
Push in side at tab  
to release  
Line up tabs and  
press in side to  
attach  
Back Wire (either hole may  
be used)  
Back wire openings use #14-12  
AWG solid copper wire only.  
Green or bare copper wire in wall box to Green terminal screw.  
Line Hot (common) wall box wire identified (tagged) when  
removing old switch to terminal screw marked “BK”.  
Side Wire Connection  
Side wire terminals accept  
#14 AWG solid copper wire only.  
NOTE: If insulating label is not affixed to terminal screw marked  
"YL/RD", use electrical tape to cover.  
Installing Dimmer by itself or with other devices:  
2
1
2
1
Proceed to Step 5.  
First Traveler wall box wire to terminal screw marked “RD” (note  
wire color). This traveler from the dimmer must go to the  
terminal screw on the remote marked “RD”.  
If installing Dimmer in a single device application, proceed with the  
INSTALLING YOUR DIMMER section. If installing Dimmer in a  
multi-device application, proceed as follows:  
Make sure that the ends of the wires from the wall box are  
straight (cut if necessary).  
Remove insulation from each wire in the wall box as shown.  
3
4
5
3
4
3-Way Wiring with Coordinating Dimming  
or Switching Remote (no LEDs)  
Remove Red insulating label from terminal screw marked  
“YL/RD”.  
Second Traveler wall box wire to terminal screw marked “YL/RD”  
(note wire color). This traveler from the dimmer must go to the  
terminal screw on the remote marked “YL/RD”.  
Step 4b  
MULTI-DEVICE APPLICATION:  
In multi-dimmer installations, the reduction of the dimmer’s capacity  
is required. Refer to the chart for maximum load per dimmer.  
For Single-Pole Application, go to Step 4a.  
(Coordinating Dimming Remote Depicted)  
For 3-Way Coordinating Remote (no LEDs) Application, go  
to Step 4b.  
Coordinating Remote  
Dimmer  
For 3-Way Matching Remote (with LEDs) Application, go to  
Step 4c.  
Single-Pole  
3-Way  
WIRING COORDINATING REMOTE:  
Connect wires per WIRING DIAGRAM as follows:  
NOTE: Maximum wire length from dimmer to last remote is 300ft.  
1. Line (Hot)  
2. Neutral  
3. Ground  
4. Load  
1. Line or Load (See important  
instruction below)  
2. Neutral  
BK  
BK  
Terminal  
Screw marked  
Black (BK)  
1
1
Single-Pole Wiring Application:  
2
Step 4a  
2
Green or bare copper wire in wall box to Green terminal screw.  
Load wall box wire identified (tagged) when removing old switch  
to terminal screw marked “BK”.  
3. Ground  
3
4
3
4. First Traveler – note color  
5. Second Traveler – note color  
NOTE: For matching remote w/LEDs  
installation, the First Traveler becomes  
Line Hot.  
RD  
Terminal  
Screw marked  
Yellow/Red  
(YL/RD)  
YL/RD  
RD  
4
YL/RD  
First Traveler wall box wire (note color as above) to terminal  
screw marked “RD”. This traveler from the remote must go to  
the terminal screw on the dimmer marked “RD”.  
Second Traveler wall box wire (note color as above) to terminal  
screw marked “YL/RD”. This traveler from the remote must go  
to the terminal screw on the dimmer marked “YL/RD”.  
5
5
BK  
Terminal  
1
3
Terminal  
Screw marked  
Black (BK)  
2
Screw marked  
Red (RD)  
MAXIMUM LOAD PER DIMMER FOR MULTI-DEVICE  
More than  
IMPORTANT: For 3-Way applications, note that one of the screw  
terminals from the old switch being removed will usually be a  
different color (Black) or labeled Common. Tag that wire with  
electrical tape and identify as the common (Line or Load) in both  
the dimmer wall box and remote wall box.  
Terminal  
Screw marked  
Yellow/Red  
(YL/RD)  
RD  
YL/RD  
4
Terminal  
Screw marked  
Red (RD)  
Remote terminal screw marked "WH" should have White  
insulationlabel affixed.  
Cat. No.  
Single  
Two Devices 2 Devices  
VZI  
Ø
6
600W  
500W 400W  
NOTE: If insulating label is not affixed to terminal screw marked  
"WH", use electrical tape to cover.  
Terminal Label:  
Use Terminal for 3-Way or More Applications Only.  
For Single-Pole Applications, Do Not Remove This  
Label.  
Proceed to Step 5.  
 

Lenmar Enterprises Battery Charger BCUNI2 User Manual
LG Electronics Computer Monitor E2250V User Manual
Lincoln Electric Welder SVM114 C User Manual
Linear Satellite Radio XT 4 User Manual
Little Tikes Baby Gym Baby Gym User Manual
Lochinvar Boiler 81 286 User Manual
Lowrance electronic SONAR X 40 User Manual
Makita Drill HR4001C User Manual
Marshall Amplification Music Mixer BB 2 User Manual
MGE UPS Systems Power Supply Rackmount PDU User Manual